PARTS

La San Marco 1/4" Ball ValveBrand-specific ball valve for select La San Marco models that isn't listed in any factory parts diagram. These machines use pipe ends with smaller ferrules than the espresso-industry standard, so a generic 1/4" ball valve won't seal correctly.SPECIFICATIONSConnections: 1/4"...

1/4" F x 1/4" M Ball ValveA chrome-plated brass ball valve with 1/4" female x 1/4" male British Standard Pipe threads, used across a wide range of commercial espresso equipment brands.COMPATIBILITY Fits: select models of Bezzera, BFC, Conti, Expobar, Fiorenzato (C.S.), Gaggia, Grimac, Nuova...

1/4" BSP Female Coupling FittingThis generic brass coupling joins two 1/4" female BSP lines for general plumbing applications.SPECIFICATIONSThread: 1/4" F x 1/4" F BSPCOMPATIBILITY Fits: any 1/4" BSP female plumbing application Replaces: SKU V_897 INSTALLATIONDIY-friendly plumbing fitting.

30 cm Stainless Steel Water Supply Hose, 1/4" BSP FemaleThis braided stainless steel water supply hose has 1/4" female BSP (parallel) fittings with conical seats on both ends - a convenient roughly foot-long length for plumbing an espresso machine into a water line or...

1/4" F Flare x 3/8" Push-in Hose ConnectorA DM Fit brand connector that adapts a 1/4" female flare fitting to 3/8" push-in tubing. Flare fittings are relatively uncommon in this industry, most fittings you'll encounter are compression, NPT, or BSP, so don't confuse this...

1/4" Female Flare to 3/8" Barb AdapterThis brass adapter threads onto our 9001B (07C07-116) Black Quick Disconnect fitting, converting its outlet to a 3/8" hose barb for polyvinyl fresh water supply line. It's the piece you need when you're plumbing a quick-disconnect water hookup...

1/4" F BSP x 3/8" M BSP Adapter FittingCommon parallel-thread (British Standard Pipe) adapter fitting, stepping down from 3/8" male to 1/4" female.SPECIFICATIONSThread: 1/4" F BSP x 3/8" M BSP (parallel)INSTALLATIONSimple DIY swap with a wrench.

La San Marco 10mm Stainless Steel BallA 10mm stainless steel ball used in the exhaust valve of La San Marco manual (non-FCS) groups.SPECIFICATIONS Material: Stainless steel Diameter: 10 mm COMPATIBILITYFits: La San Marco manual group exhaust valves (NOT the FCS group)INSTALLATIONA quick DIY swap...

10mm Infusion Valve PinThis infusion valve pin fits ECM and La Pavoni BAR T models, though most techs now recommend upgrading to the larger 12.1mm version instead of replacing like-for-like.SPECIFICATIONS10 x 6 x 6 mm, M3 threadCOMPATIBILITYFits: ECM, La Pavoni BAR TINSTALLATIONInternal valve component,...

107° Brew Temperature ThermostatAn M4-threaded-stud thermostat (KSD301-P) that regulates brewing temperature at 107°C. Used in the Brasilia Club and Lady models, as well as the Gaggia Carezza, Classic, and Evolution, Gaggia part #DM1168.SPECIFICATIONS Trip temperature: 107°C Model: KSD301-P Mount: M4 threaded stud COMPATIBILITY Fits:...

100°C Safety ThermostatAn M4 thread-stud safety thermostat rated to trip at 100°C. Also suitable for applications in Isomac, Gaggia, and Saeco equipment.SPECIFICATIONS Trip temperature: 100°C Thread: M4 stud COMPATIBILITY Fits: Ascaso, Isomac, Gaggia, and Saeco equipment using an M4 thermostat mount Replaces: I..374 INSTALLATIONDIY-friendly,...

100° C Pump High-limit ThermostatThis 100°C high-limit thermostat monitors vibratory pump temperature and cuts power to the pump if it starts to overheat. This is a special order item shipped directly from the manufacturer separately from the rest of your order: in-stock units ship...

100 µf start capacitor for 110V Rancilio MD-80 grinder. Fast shipping when in stock. When out of stock this becomes a special order item and typically requires 2-4 weeks for processing prior to shipping. Specifications:Capacity: 100 µf Compatibility:Rancilio MD-80 110V Installation: Direct capacitor replacement...

10 µF Two-Pole Pump Motor CapacitorTwo-terminal 10 µF run capacitor used on espresso machine pump motors. A weak or failed capacitor is a common cause of a pump that hums but won't build pressure, or won't start at all.SPECIFICATIONS10 µF, two voltage terminalsCOMPATIBILITYWorks with:...

10 µF Start CapacitorA 10 µF motor start/run capacitor rated for 450V at 50/60Hz, used across a range of espresso machine and pump motors. Four-terminal design for flexible wiring.SPECIFICATIONS 10 µF, 450V, 50/60Hz Four voltage terminals Lead connector: 6.35 x 0.8 mm Dimensions: 36...

10 x 2.5 mm PTFE gasket for hot water spigot. Specifications: Dimensions: 10 x 2.5 mm Material: PTFE La Marzocco part #: L169/A1 Compatibility:La Marzocco models with hot water spigot Installation: Replace gasket on hot water spigot Recommended for qualified technician.

10mm Hose End FittingA hose end fitting designed to pair with part V_485. Out of production, with limited stock available.SPECIFICATIONSWidest barb outside diameter: 11.5 mmCOMPATIBILITYWorks with: V_485 INSTALLATIONSimple DIY hose fitting.PRO TIPSThis is an out-of-production part with limited remaining stock, if you're pairing it...

1/8" BSP Fitting, Male to FemaleStraight 1/8" BSP pipe fitting, male to female.COMPATIBILITYWorks with: a slightly longer brass version is also available, W25742 INSTALLATIONSimple DIY swap with a wrench.

1/8" x M7 Barb Expansion ValveExpansion valve fitting used in the Nuova Simonelli Oscar as well as the Victoria Arduino Venus Bar and Venus Century models.SPECIFICATIONS Thread: 1/8" Male British Standard Pipe Barb: M7 COMPATIBILITYFits: Nuova Simonelli Oscar, Victoria Arduino Venus Bar, Victoria Arduino...

Rancilio Silvia Pro/X Push-In Hose Fitting - 1/8" x 6mmOEM push-in fitting for new-version boilers on the Rancilio Silvia Pro and Silvia Pro X, with 1/8" threads sized for 6mm tubing.SPECIFICATIONS1/8" threads, for 6mm push-in tubing, new-version boilers onlyCOMPATIBILITY Fits: Rancilio Silvia Pro and...